男男巨黄肉车文play文_日本一二三区高清_小说肉文h_粗喘撞吟np文古代

Welcome to the official website of the Taian Haishu Machinery Co., Ltd.,Service Phone:0086-0538-8606169ChineseEnglishSitemapEnterprise MailboxContact Us

Sale Of CNC Lathe

Senior Expert Of CNC Lathe

Global Service Hotline

0086-0538-8606169

Notice:
Warm congratulations "HAISHU" brand CNC machine tool exports reached 40 countries. They are: the United States, Britain, Germany, Sweden, Italy, Russia, Turkey, New Zealand, Colombia, South Korea, Bahrain, South Africa and other countries. "HAISHU" brand has been known at home and abroad.
Contact Us
Global Hotline:
+86-538-8606169

Taian Haishu Machinery Co.,Ltd.

Telephone: +86-538-8606169

Fax: +86-538-8606169

Address: Zhouwangzhuang Village, Shankou Town

             Taian City Shandong Province China

Current Location:Home Page » News » Industry News
How the cycle voltage of wheel hub CNC lathe power supply voltage
From:Taian Haishu Machinery Co.,Ltd. Updatetime:2017-8-24 13:46:59 Views:
Taian sea number of machinery main products: horizontal inclined bed CNC lathes, vertical CNC lathes, wheel CNC lathes, CNC turning centers, CNC pipe thread lathes, CNC milling machines, CNC machining centers, the purchase of CNC lathes to

How the cycle voltage of wheel hub CNC lathe power supply voltage
Check the sequence of the method is very simple, one is measured with the phase sequence table, as shown in Figure 3-2a, when the phase sequence is correct when the phase sequence clockwise rotation, otherwise it is phase sequence error,
Will R, S, T any two wires connected to adjust the position on the line. The other is to use two-wire oscilloscope to observe the waveform between the two phases, two phase phase difference in the phase 1200.
Verify that the DC power supply output is short to ground. A variety of CNC system has a DC power supply unit, for the system to provide the required +5 V, ± 15V, ± 24V and other DC voltage. Turn on the control cabinet power supply, check the output voltage.
Before the power is turned on, the motor power line can be disconnected first to ensure safety. In this way, the system will not cause small CNC lathe work. But should be based on the description of the repair instructions on the speed control unit to make some necessary settings, not due to disconnect the motor power line caused by the alarm. Turn on the control cabinet power, the first check the cabinet inside the fan
Whether it is rotating, which is to determine whether the power supply is the most convenient way. Then check the printed circuit board voltage is normal, all kinds of DC voltage is within the allowable range.
Confirmation of fluctuation range of power supply voltage. Check whether the user's power supply voltage fluctuation range is within the allowable range of the CNC system. General CNC system allows the voltage fluctuation range of 85 ~ 110% of the rated value,
Enter the confirmation of the supply voltage phase sequence. At present, the feed control unit of the CNC small CNC lathe and the power supply of the spindle control unit are mostly controlled by the crystal tube. If the phase sequence is not connected, the power supply of the feed control unit may be blown.
Fuse is the device "guardian", always protect the safety of equipment. In addition to the main line on the power supply fuse, almost every circuit board or circuit unit are equipped with fuses, when the overload, the external voltage is too high or the load side of an unexpected short circuit, the fuse can be immediately cut off and cut off the power, Protect the role of equipment, so be sure to check the quality of the fuse
Quantity and specifications are met.
Taian sea number of machinery main products: horizontal inclined bed CNC lathes, vertical CNC lathes, wheel CNC lathes, CNC turning centers, CNC pipe thread lathes, CNC milling machines, CNC machining centers, the purchase of CNC lathes to select the sea, Yes, order phone 13953800780.
More CNC lathe knowledge at http://badinfluencefilms.com/

  【Close】
News
Product

CNC lathe research and development, every problem we can not be ignored!

How to make my machine have a longer service life?

How to make the equipment have higher production efficiency?

How to ensure that the machine is simple to learn?

... ...

Learn CNC lathes

From the beginning our website!

Global Service Hotline:+86-0538-8606169

Service Center Contact Us
Message
Service
Common Question

Taian Haishu Machinery Co., Ltd.
Address:Zhouwangzhuang Village, Shankou Town Taian City Shandong Province China
Telephone:+86-538-8606169
Fax:+86-538-8606169
Copyright © 2015 HaiShu All rights reserved.